YFD300100-F
UV lamp parameters
名称name | 江南app的下载方式是什么 UVLEDsurface light source | ||
芯片chip | 韩国LG芯片Seoul chip | 功率power | 700W |
光功率Optical power | 1000-3000mwcm2 | 波长wavelength | 365nm |
输入input | 40V、4.2A | 功率power | 0-100% |
辐射面Radiation surface | 300X100mm | 散热dissipate heat | 风冷Air cooling |
环境温度ambient temperature | -10℃~50℃ | 芯片寿命Chip life | 20000H |
实拍UV灯头图
产品特点Product features
1)无需预热,即开即用;
No preheating, ready to use
2)不含汞,既安全又环保;
Mercury free, safe and environmentally friendly
3)产品功率小,节能省电;
Product power is small, energy saving
4)设备结构简洁大方,轻便,易集成;
The equipment structure is simple, light and easy to integrate
5)江南app
,无热辐射,降低了固化过程产生的热量;
Cold light source, no thermal radiation, reduce the heat generated during the curing process
6)采用精密的光学分析技术,光效率密度高,均匀性高达90%以上;
Using precise optical analysis technology, the optical efficiency density is high, and the uniformity is more than 90%
7)采用韩国LG垂直结构LED紫外灯珠,寿命长达20000小时以上。
It adopts Korean LG vertical structure led UV lamp bead, with a service life of more than 20000 hours.
参数设置Parameter setting
开机画面Boot screen
按下“Welcome”按钮画面如下Press the "welcome" button, and the screen is as follows
能量值:UV灯功率0-100%(Energy value: UV lamp power 0-100%)
自动模式:按下启动UV灯亮倒计时开始,时间到灯灭。
(Automatic mode: press start UV light, countdown start, time to light out.)
手动模式:按下启动UV灯亮,按下停止UV等灭。
(Manual mode: press to start UV light on, press to stop UV light off.)
倒计时:时间设定大于0时才会显示
(Countdown: only when the time setting is greater than 0)
温度:显示铜基板上的温度
Temperature: displays the temperature on the copper substrate
启动:按下灯亮(Start: press the light to light up)
停止:按下灯灭(Stop: press the light to go out)
灯亮时按钮指示灯亮、灭时指示灯灭
(When the light is on, the button indicator light is on, and when it is off, the indicator light is off)
温度超温报警时UV灯不亮
参数设置界面Parameter setting interface
照射时间:设置为自动模式时时间计时有效
Irradiation time: the time is valid when it is set to automatic mode
运行时间:UV灯累计时间
Running time: UV lamp cumulative time
报警温度:设定报警时温度,设置范围0-100℃
Alarm temperature: set the alarm temperature, setting range 0-100 ℃
电箱端子接线图
UVLED be careful when using the product:
Whether the fan port is covered by other objects
Lamp cap: when using UV LED lamp cap, it is recommended to clean the glass surface of lamp cap with alcohol once a week, and use air gun or vacuum cleaner to remove excessive dust and garbage inside the controller and on the grid.
Electric box: once a month on a regular basis, use air gun or vacuum cleaner equipment to remove the dust on the fan of the electric box, so as to prevent excessive dust for a long time from reducing the heat dissipation of the electric box and reducing the service life of the electric box.
Note: before maintenance, be sure to cut off the power supply, pull out the power cord, and after maintenance, the equipment can be used only after it is completely dry to prevent danger.